Garage door repair in Bloomfield Hills and Oakland County, 7 AM to 10 PMCall the office: (248) 587-8430

Garage Door Track Repair

Tracks straightened, braced and aligned — across Bloomfield Hills, Birmingham, West Bloomfield, Troy, Franklin, Beverly Hills, Rochester Hills, Orchard Lake Village.

Garage door track repair restores the rails the door rides in, and the cause is usually a bump, loose fasteners or a door that was forced while it was jammed. A sectional door runs in two vertical tracks beside the opening that curve into horizontal tracks overhead. The tracks must be plumb, parallel and spaced so the rollers fit with a little play; if they drift, the door binds, scrapes or hops out.

We check the track faces for dents and twists, tighten or replace the brackets, re-anchor loose track to the jamb and ceiling, and measure the gap between track and jamb at the top and bottom, which the trade calls track graduation. A mildly bent section can be straightened; a creased or kinked track is replaced, because a straightened crease keeps flexing. Then the door is run by hand, and under the opener, until it closes square against the weatherstrip.

Track Damage to Look For

  • The door scrapes or catches on one side as it rises
  • A visible dent, crease or kink in a vertical track
  • Track brackets pulling loose from the jamb or wall
  • Gaps between the door and the weatherstrip on one side
  • A roller that pops out at the same spot every cycle
  • Horizontal tracks that sag or tilt in the ceiling

❄️ The Oakland County Freeze-Thaw Factor

Freeze and thaw loosen fasteners and the wood they bite into. The NOAA 1991–2020 normals for the Pontiac station give about 135 days a year with freezing lows, 47 of which stay frozen all day, which leaves roughly 88 days of swings across freezing. Damp wood jambs swell and shrink with those swings, screws work loose and brackets slacken a little each winter. The bracket does not snap; it lets the track drift until the rollers drag.

We re-anchor tracks into solid framing with lag screws where the original screws have lost their grip, and we check both sides after every repair.

How We Handle It

Step 1

Sight the rails

Both tracks are checked for dents, twists and plumb, and the gap to the jamb is measured at the top and the bottom.

Step 2

Quote the fix

You get the exact price on site, track straightened or replaced, with the brackets named.

Step 3

Straighten, replace, re-anchor

Bent sections are corrected or swapped, loose brackets replaced and fasteners set into solid framing.

Step 4

Run the door

The door is cycled by hand and under power until the rollers glide, the seal meets the floor evenly and nothing rubs.

Technician standing in a garage beneath a raised wood-grain garage doorTechnician on a ladder squaring an upright track at the edge of the door opening

Track Repair Starting Price

Track Repair & Off-Track Door per door
From $150
Diagnostic Service Call $0 with a completed repair
$0

This price covers straightening and re-fastening the track on one door; any replacement track pieces are added to the quote first.

Garage Door Track Repair — FAQs

What does straightening a bent track cost?
Track and off-track work starts from $150 per door, and the exact quote on site before any work starts gives the real number for your door. The final figure depends on the track length, whether a bend can be corrected or a section must be replaced, and the brackets involved.
Is a bent track always replaced, or can it be fixed?
A mildly bent track can be straightened, but a creased or kinked track should be replaced. A crease keeps flexing with every cycle, so a straightened crease usually bends again.
What makes one side of the door scrape as it moves?
A door that rubs on one side usually has a track that has drifted out of plumb, a loose bracket or a roller that has worn. We measure the gap between track and door at the top and bottom, tighten or re-anchor the track and replace any worn roller.
Why do garage door tracks come loose?
Tracks come loose from vibration, freeze-thaw movement in the wood jamb, and screws that bit into a soft spot. Each cycle shakes the fasteners a little, so a bracket that was snug in October can be slack by March. We re-anchor into solid framing.
Can I tap a bent garage door track back with a hammer?
No. The tracks carry the door under spring tension, and a hammer can crimp the rail and make the bind worse. DASMA's inspection checklist says not to try to remove, repair or adjust springs, cables, steel brackets or mounting parts yourself.
Contact

Talk to the Belle Team

Phone us from 7 AM to 10 PM, or leave your details and a quick description of the problem and we will call back to set a time.

☎ Call (248) 587-8430 Open in Google Maps

Request a call back

Your details are used only to answer your request. Privacy Policy.

☎